Replacing Clutch Cable

gaillarry · 02-26-2013, 12:22 PM

Putting on a new clutch cable. I removed the linkage from the shaft but can't remember which way it goes back on. I see a slash mark on the top of the shaft, is there a certain way that it installs on the linkage?

Water Warrior 2 · 02-26-2013, 03:25 PM

If that is a "before" pic then install it the same way with the new cable. Use a dab of blue loktite on the threads of the bolt.

gaillarry · 02-27-2013, 09:22 AM

Quote:

Originally Posted by Water Warrior

If that is a "before" pic then install it the same way with the new cable. Use a dab of blue loktite on the threads of the bolt.

I wish it was a before pic but I just sat the linkage on the shaft and there's not enough tension on the cable, so I"ll try to align the hash mark with the gap in the linkage.

blaine · 02-27-2013, 10:05 AM

Quote:

Originally Posted by gaillarry

Quote:

Originally Posted by Water Warrior

If that is a "before" pic then install it the same way with the new cable. Use a dab of blue loktite on the threads of the bolt.

I wish it was a before pic but I just sat the linkage on the shaft and there's not enough tension on the cable, so I"ll try to align the hash mark with the gap in the linkage.

IIRC your right the gap in the linkage lines up with the slash mark. (no longer have my G.Z. to check for you)

:cool:

alantf · 02-28-2013, 05:59 AM

[attachment=0:3cm8xb7l]Picture 008.jpg[/attachment:3cm8xb7l]My 2007 (European) doesn't have the slot. Could a previous owner have done it? Anyhow, here's a picture of mine (never been taken off the splines) so you can compare the angle.

alantf · 02-28-2013, 06:03 AM

Just compared our photos. Looking at the bolt in relation to the flat bar, it does look as though you are slightly counter clockwise to the position of mine, so, perhaps, the slot should line up.

blaine · 02-28-2013, 09:43 AM

As long as it is positioned on the splines so the cable is tight enough for you to get your proper "free play" at the lever you should be good to go.

02-26-2013, 12:22 PM	#1
gaillarry Junior Member Join Date: May 2008 Location: Ontario, Canada Posts: 24	Replacing Clutch Cable Putting on a new clutch cable. I removed the linkage from the shaft but can't remember which way it goes back on. I see a slash mark on the top of the shaft, is there a certain way that it installs on the linkage? Login or Register to Remove Ads
	0

02-26-2013, 03:25 PM	#2
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	Re: Replacing Clutch Cable If that is a "before" pic then install it the same way with the new cable. Use a dab of blue loktite on the threads of the bolt.
	0

02-28-2013, 05:59 AM	#5
alantf Senior Member Join Date: Nov 2008 Location: Tenerife (Spain) Posts: 3,719	Re: Replacing Clutch Cable [attachment=0:3cm8xb7l]Picture 008.jpg[/attachment:3cm8xb7l]My 2007 (European) doesn't have the slot. Could a previous owner have done it? Anyhow, here's a picture of mine (never been taken off the splines) so you can compare the angle. __________________ By birth an Englishman, by the grace of God a Yorkshireman. Login or Register to Remove Ads
	0

02-28-2013, 06:03 AM	#6
alantf Senior Member Join Date: Nov 2008 Location: Tenerife (Spain) Posts: 3,719	Re: Replacing Clutch Cable Just compared our photos. Looking at the bolt in relation to the flat bar, it does look as though you are slightly counter clockwise to the position of mine, so, perhaps, the slot should line up. __________________ By birth an Englishman, by the grace of God a Yorkshireman.
	0

02-28-2013, 09:43 AM	#7
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	Re: Replacing Clutch Cable As long as it is positioned on the splines so the cable is tight enough for you to get your proper "free play" at the lever you should be good to go. __________________ If at first you do succeed, try not to look surprised.
	0

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode