Forum: Troubleshooting
10-16-2017, 02:09 AM
|
|
Replies: 12
Views: 8,389
|
|
Forum: Other Models/Manufacturers
11-15-2016, 01:44 AM
|
|
Replies: 27
Views: 37,570
Nice ride. I think the C50 is the more modern...
Nice ride. I think the C50 is the more modern version of my VZ800. Sadly, my VZ800 has a hole in the engine case and I am not sure it will ever run again. I have yet to unmount the engine and pull...
|
|
Forum: General GZ250 Talk
11-15-2016, 01:39 AM
|
|
Replies: 70
Views: 36,199
|
|
Forum: Troubleshooting
09-09-2016, 02:01 AM
|
|
Replies: 4
Views: 6,836
|
|
Forum: General GZ250 Talk
09-09-2016, 01:42 AM
|
|
Replies: 2
Views: 5,969
|
|
Forum: Off-Topic Discussion
02-17-2016, 02:21 AM
|
|
Replies: 48
Views: 62,129
|
|
Forum: General GZ250 Talk
11-17-2015, 09:22 PM
|
|
Replies: 7
Views: 6,071
|
|
Forum: General GZ250 Talk
11-17-2015, 12:55 AM
|
|
Replies: 7
Views: 6,071
I ended up with a Pirelli Route 66 on the rear...
I ended up with a Pirelli Route 66 on the rear and had a Pirelli Sport Demon touring tubeless type installed (with a tube). The dealer said he couldn't find a tube type tire for the front so I went...
|
|
Forum: General GZ250 Talk
11-14-2015, 10:16 PM
|
|
Replies: 3
Views: 4,654
I put Shinkos on my Suzuki VZ 800 and they are...
I put Shinkos on my Suzuki VZ 800 and they are doing nicely. Got a 3 inch nail in the rear after the first 800 miles and did a plug and patch and holding up very nicely 2,800 miles later. I like...
|
|
Forum: Troubleshooting
10-16-2015, 12:57 AM
|
|
Replies: 6
Views: 6,859
|
|
Forum: Member Introductions
10-16-2015, 12:45 AM
|
|
Replies: 5
Views: 3,931
|
|
Forum: Member Introductions
10-11-2015, 01:51 AM
|
|
Replies: 12
Views: 7,759
|
|
Forum: Riding Safety & Tips
10-11-2015, 01:49 AM
|
|
Replies: 13
Views: 22,145
It is a good lesson learned and, while painful...
It is a good lesson learned and, while painful and inconvenient to have a fracture, at least not too bad in the overall scheme of "what could have been." Most folks here believe in ATGATT, I think. ...
|
|
Forum: General Maintenance
10-11-2015, 01:40 AM
|
|
Replies: 19
Views: 12,264
|
|
Forum: Member Introductions
06-01-2015, 02:19 AM
|
|
Replies: 5
Views: 3,790
|
|
Forum: Member Introductions
05-10-2015, 07:59 PM
|
|
Replies: 6
Views: 3,680
|
|
Forum: Parts & Accessories
05-03-2015, 07:16 PM
|
|
Replies: 3
Views: 4,363
|
|
Forum: Ride Reports & Meets
04-08-2015, 12:01 AM
|
|
Replies: 6
Views: 11,378
|
|
Forum: Member Introductions
03-29-2015, 12:03 AM
|
|
Replies: 8
Views: 3,612
|
|
Forum: Member Introductions
03-28-2015, 11:58 PM
|
|
Replies: 6
Views: 3,404
|
|
Forum: Troubleshooting
03-28-2015, 11:16 PM
|
|
Replies: 8
Views: 5,414
Hmmm...I wasn't aware that the valve clearances...
Hmmm...I wasn't aware that the valve clearances were printed on any sticker. The manual says intake: 0.03-0.08 mm (0.001-0.003 in) and exhaust: 0.08-0.13 mm (0.003-0.005 in). So, assuming you used...
|
|
Forum: General GZ250 Talk
01-20-2015, 12:50 AM
|
|
Replies: 7
Views: 7,439
There is a guy who did a cross country and back...
There is a guy who did a cross country and back trip on a Ninja 250 (I think I got the video link from this board, but will look to see if I can find it). In the meantime, try a YouTube search under...
|
|
Forum: Member Introductions
01-13-2015, 01:09 AM
|
|
Replies: 10
Views: 8,248
|
|
Forum: Troubleshooting
11-27-2014, 01:33 AM
|
|
Replies: 5
Views: 4,844
Can a petcock be soldered??
Hi all!
This question is actually with respect to my Suzuki Marauder VZ800, but it could happen to any bike. The nipple from the petcock that attaches to the fuel line below the shut off snapped...
|
|
Forum: General GZ250 Talk
11-27-2014, 01:14 AM
|
|
Replies: 12
Views: 11,414
|
