Forum: GZ250 Media
10-19-2014, 12:38 AM
|
|
Replies: 23
Views: 13,401
holes in exhaust
Yeah:ride:
:shrug: Pretty much :coffee: just to annoy :lmao:
It made it significantly loud:tup:er.
|
|
Forum: Troubleshooting
10-19-2014, 12:27 AM
|
|
Replies: 3
Views: 4,761
Unscrew the little cap on the carb and pull a...
Unscrew the little cap on the carb and pull a little on the cable. A little piston with a pin on the end should slide out. If it's broken you might need to get a screw extractor in there to get it...
|
|
Forum: Troubleshooting
10-19-2014, 12:24 AM
|
|
Replies: 8
Views: 8,806
|
|
Forum: Troubleshooting
10-19-2014, 12:20 AM
|
|
Replies: 6
Views: 6,383
|
|
Forum: Troubleshooting
06-06-2014, 12:53 PM
|
|
Replies: 36
Views: 21,999
|
|
Forum: Troubleshooting
06-03-2014, 08:02 PM
|
|
Replies: 36
Views: 21,999
|
|
Forum: Performance
06-03-2014, 07:33 PM
|
|
Replies: 7
Views: 6,777
Yeah, it runs well with the new setup. I'm...
Yeah, it runs well with the new setup. I'm tempted to say it runs better, but that might just be the money I spent to set it up talking.
Two things for sure: it runs cooler after the re jet and it...
|
|
Forum: Performance
06-03-2014, 07:30 PM
|
|
Replies: 9
Views: 6,794
I use a pod filter. It works fine.
I don't...
I use a pod filter. It works fine.
I don't know if there's much mechanical difference between the two. The main thing I think would be the look.
Someone correct me if I'm wrong about that.
|
|
Forum: Troubleshooting
05-30-2014, 05:55 PM
|
|
Replies: 9
Views: 5,546
|
|
Forum: Troubleshooting
05-30-2014, 03:09 AM
|
|
Replies: 34
Views: 12,005
Your valve... broke off? Wow.
Ebay is where...
Your valve... broke off? Wow.
Ebay is where I would look first, then maybe a salvage yard, then probably a Suzuki dealer. Good luck.
Remember to support the cam chain from falling down into...
|
|
Forum: Troubleshooting
05-30-2014, 02:24 AM
|
|
Replies: 36
Views: 21,999
|
|
Forum: Troubleshooting
05-30-2014, 02:17 AM
|
|
Replies: 12
Views: 6,802
So I assume the starter is cranking the engine...
So I assume the starter is cranking the engine which means you have power. I'd throw a new plug in there first even though it tested good on your lawnmower just to be on the safe side. You could try...
|
|
Forum: General GZ250 Talk
05-29-2014, 02:04 PM
|
|
Replies: 10
Views: 8,878
Your seat shouldn't wobble with or without the...
Your seat shouldn't wobble with or without the storage insert. Check to see if one of those metal tabs on each side are bent, check if the latch is screwed all the way in to the rear fender bracket,...
|
|
Forum: GZ250 Media
05-29-2014, 05:16 AM
|
|
Replies: 23
Views: 13,401
Ha, yeah it's intentional. I like the idea of...
Ha, yeah it's intentional. I like the idea of some moving parts exposed.
It's a brand new chain. Not saying sh.t doesn't happen, but I'm not too worried about it. Plus the way the chain is routed...
|
|
Forum: Troubleshooting
05-29-2014, 05:06 AM
|
|
Replies: 66
Views: 23,675
|
|
Forum: Troubleshooting
05-28-2014, 10:17 PM
|
|
Replies: 66
Views: 23,675
|
|
Forum: Performance
05-28-2014, 10:04 PM
|
|
Replies: 7
Views: 6,777
|
|
Forum: Performance
05-28-2014, 06:25 PM
|
|
Replies: 12
Views: 56,933
I drilled four 1/2 inch holes in the end of my...
I drilled four 1/2 inch holes in the end of my exhaust and it made it a bit louder.
As for the idle problem, try cleaning the carb jets, check the condition of the rubber on the needle valve and...
|
|
Forum: Gadgets & Farkles
05-28-2014, 05:50 PM
|
|
Replies: 3
Views: 5,961
The same thing happened to me, but I was lucky...
The same thing happened to me, but I was lucky enough to notice before it burned all the way through. I modified the straps the go over the fender by punching more holes in them so the bags sat up...
|
|
Forum: Gadgets & Farkles
05-28-2014, 05:45 PM
|
|
Replies: 20
Views: 31,207
|
|
Forum: GZ250 Media
05-28-2014, 05:30 PM
|
|
Replies: 8
Views: 6,248
|
|
Forum: Performance
05-28-2014, 05:25 PM
|
|
Replies: 6
Views: 19,034
Actually the 6sigma kit only had parts that...
Actually the 6sigma kit only had parts that either fit or were specific to the GZ. Not too expensive either ($50 including shipping). I definitely recommend them if you ever need a jet kit for...
|
|
Forum: GZ250 Media
05-28-2014, 05:18 PM
|
|
Replies: 23
Views: 13,401
New to the forum
Hey, I just joined this forum. Psyched that there are so many people who consistently post on here about their GZ's. Here are some pictures of mine - I've been messing around with it a bit lately....
|
|
Forum: Performance
05-28-2014, 03:01 PM
|
|
Replies: 6
Views: 19,034
Carb slide - vacuum piston modifications
Hello. I recently bought a jet kit from this company 6sigma racing. Along with some jets and needle shims, they sent me a #59 (very very small) drill bit to drill out an additional vacuum hole in the...
|
