Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > GZ250-Specific > Instructional Articles

Reply
 
Thread Tools Display Modes
Old 05-05-2017, 06:07 PM   #1
leonj2932
Member
 
Join Date: May 2017
Location: San Francisco/Bay Area
Posts: 31
Oh No Electrical Problems

Hello all , I am currently having lighting issues with my 2007 gz250 . I used my emergency lights after getting lost and after turning the bike back on all turn signals wear dead . and the turn signal indicator light (the small green one) was no longer working. First of all all my lights except headlight and rear brake light (only when brakes are applied ) still function. This means that my brake light will only light up if i apply the brake . Is that normal ?? I remember it always on before. none of my turning lights work . or stay on at any time. So i replaced all the turning light bulbs with bulbs from autozone, the front turning signals are now always lit up . The rear turning signals still will not function even with new bulbs !! and the turning light switch to indicate which way I am going doesn't seem to work . I push the switch left or right and neither the front or rear turn signals flash. Can you guys please help me? I have searched endlessly and have found no answer to this problem. I cant ride my motorcycle anymore because i use it to commute and i cant possible keep risking riding at night without any form of lighting in the back . Please help , dont just refer to other forums , unless you provide a link . Also battery has been tested and runs fine so thats not the issue. Thank you all in advance



Login or Register to Remove Ads
leonj2932 is offline  
Reply With Quote
Old 05-05-2017, 08:14 PM   #2
blaine
Senior Member
 
blaine's Avatar
 
Join Date: Feb 2010
Location: P.E.I. Canada
Posts: 3,784
Your brake light should only come on when brake is applyed (Thats correct) But the tail light part (Double contact bulb 1157) shpuld come on with key.....Did you replace front bulbs with double contact 1157 & rear with 1156 single contact?...Also check your fuses.
__________________
If at first you do succeed, try not to look surprised.



Last edited by blaine; 05-05-2017 at 08:18 PM.
blaine is offline  
Reply With Quote
Old 05-06-2017, 01:52 AM   #3
5th_bike
Senior Member
 
5th_bike's Avatar
 
Join Date: Oct 2007
Location: HoCo, Maryland
Posts: 1,349
I agree with Blaine, from what you wrote it seems that you put the wrong bulbs in. The front turn signal bulbs and the rear brake light bulbs have two filaments in them, and two separate contact spots at the bottom.
__________________
2005 "Saturn Black", stock + tach



Login or Register to Remove Ads
5th_bike is offline  
Reply With Quote
Old 05-12-2017, 06:50 PM   #4
leonj2932
Member
 
Join Date: May 2017
Location: San Francisco/Bay Area
Posts: 31
hey guys sorry for the slow response time. I had several issues but i do not have the wrong size bulbs. It was just a matter of not actually knowing what was supposed to be working and what wasn't actually working properly. All issues have been fixed by replacing the bulbs. The turn signals all work now with the correct bulbs. And the issue with my brake light was that the running light filament had blown out but the bottom filament that only comes on when you apply brake pressure was still functioning perfectly so i was confused as to if it was actually working or not. I had no idea the rear brake light was also a running light so i didn't know one of the filaments had blown. As for the rear turn signals there must be a wiring issue or a bad ground or sum thing because as soon as i plug them in they stop working , but they work perfectly fine when tested on their own .
leonj2932 is offline  
Reply With Quote
Old 05-13-2017, 12:14 AM   #5
Water Warrior 2
Senior Member
 
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
Quote:
Originally Posted by leonj2932 View Post
hey guys sorry for the slow response time. I had several issues but i do not have the wrong size bulbs. It was just a matter of not actually knowing what was supposed to be working and what wasn't actually working properly. All issues have been fixed by replacing the bulbs. The turn signals all work now with the correct bulbs. And the issue with my brake light was that the running light filament had blown out but the bottom filament that only comes on when you apply brake pressure was still functioning perfectly so i was confused as to if it was actually working or not. I had no idea the rear brake light was also a running light so i didn't know one of the filaments had blown. As for the rear turn signals there must be a wiring issue or a bad ground or sum thing because as soon as i plug them in they stop working , but they work perfectly fine when tested on their own .
Leon, would you please not post the same issues in different threads on the forum. Stick with one thread and continue from there. We will respond with one answer instead of multiple answers on various threads. That will save you time and typing as well as not possibly adding any confusion. Never fear, we will help you.



Login or Register to Remove Ads
Water Warrior 2 is offline  
Reply With Quote
Reply



Tags
electrical, gz250, problems


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:41 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.