Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > GZ250-Specific > Instructional Articles

Reply
 
Thread Tools Display Modes
Old 09-11-2008, 10:27 PM   #1
Badbob
Senior Member
 
Badbob's Avatar
 
Join Date: Aug 2006
Location: Tallahassee FL
Posts: 945
How To Fix A Slippery Clutch

Blog post with images is here. Due to the way the forum handles photos and links to photos in Goggle Photos I can't easily fix the broken links.

This is not a how to for making a worn out clutch work. If your clutch is worn out or otherwise defective you should replace it. Bad clutch springs can cause similar problems. If they are bad replace them.

Read the appropriate sections in the service manual to determine what tools you need. Before you begin.

Some symptoms I experienced:
Hard acceleration as in wide open throttle. The slipping occurs in higher gears and stops as soon as you back of the throttle. This can be a bit exciting if you are trying to get out of the way of a truck at the time.

When starting up a hill in fifth gear if I didn't down shift to fourth the clutch would begin to slip. Down shifting to fourth it would continue to slip until I backed off the throttle a little and slowed down a little. After that it it was fine. This only occurred when the bike was fully loaded as in a camping trip.

Apparently, this is a common occurrence for dirt riders. They use the clutch a lot.

The clutch plates can be worn smooth or polished to the point where they do not grip each other quite as well as they should. The solution is quite simple and quite messy.

You have to take your clutch out to do this so it means an oil change. You will also need a clutch cover gasket in your hand. Trust me on this. If you take the clutch cover off without the new gasket in your hand it will tear.

Drain the oil and remove the clutch and disassemble it according to the instructions in the service manual. Once you have the clutch cage out carefully disassemble being careful not to get the plates out of order. I'm not sure the order matters much but the plates will have worn in to fit each other by now and it seems like a good idea to put them back exactly how they came out.

There are instructions in the service manual on how to check your clutch and springs. Now is the time to do that. If your clutch is OK we can proceed with getting the slipping to stop.

You will need a small piece of quality sandpaper. The wet or dry automotive sand paper will work. 200 grit was recommended but I use a piece of 80 grit sanding belt and it orked fine. What you need to do id to lightly scuff the plates with the sandpaper. If you use 200 grit or finer you don't need to be as careful. Sand the clutch pates in a radial direction. That is from the center out. Sand both the metal pressure plates and and the clutch plates on both sides keeping in the same order the came out.

Make sure you wipe everything down good and clean before reassembly. You don't want a stray piece of silicon carbide floating around in your engine. Carefully reassemble the clutch cage and reinstall. Fill with oil and your done.

Optional: You can also shim the bolts wit appropriate washers. This causes them to press tighter on the plates. I elected to do both.

After the I did this I tool the GZ out for a test ride and tried my best to get it to slip. It wouldn't do it. After two months of daily riding the clutch hasn't slipped once.

Since a picture is worth a thousand words:




Torn gasket the got fixed with some RTV because I didn't have one. It doesn't leak.


This is so I don't have to remember where the bolts go. It also helps keep from loosing them.




Look close to see the sanding scratches.








First washer didn't work. Measured the hole with calipers and took them to Lowes with me.




This washer is just right.


Reassembled and installed clutch cage.

I was really surprised at how clean it was on the inside.



Login or Register to Remove Ads

Last edited by Badbob; 01-08-2017 at 11:34 AM. Reason: Add link to Blog Posting
Badbob is offline  
Reply With Quote
Old 09-12-2008, 09:22 AM   #2
jonathan180iq
Super Moderator
 
jonathan180iq's Avatar
 
Join Date: Jan 2007
Location: Dalton, GA
Posts: 3,996
Re: How To Fix A Slippery Clutch

This is absolutely the best How-to that we have.

I'm not close to having to work on this yet. But I applaud you, sir.
jonathan180iq is offline  
Reply With Quote
Old 09-12-2008, 09:27 AM   #3
Sarris
Senior Member
 
Join Date: May 2007
Location: New Port Richey, Florida USA
Posts: 1,348
Re: How To Fix A Slippery Clutch

One of my other GZ buddies tell me that Barnett makes makes heavy duty clutch plates and springs for the GZ. I haven't checked that out personally though.

__________________
Prudent riders live longer than moron riders.



Login or Register to Remove Ads
Sarris is offline  
Reply With Quote
Old 09-12-2008, 11:02 AM   #4
music man
Senior Member
 
Join Date: Jun 2008
Location: Hot Springs Arkansas
Posts: 1,127
Re: How To Fix A Slippery Clutch

Sarris, that would be a yes on the Barnett Springs and plates, I looked on their website.


Later
__________________
"Tell me what kind of wreck you're going to have and I'll tell you what type of helmet you need." [Author Unknown]
music man is offline  
Reply With Quote
Old 09-13-2008, 11:44 AM   #5
Badbob
Senior Member
 
Badbob's Avatar
 
Join Date: Aug 2006
Location: Tallahassee FL
Posts: 945
Re: How To Fix A Slippery Clutch

There was nothing wrong with my clutch other the being slick from over use. I considered just replacing it but being cheap I figured I had nothing to loose by fixing it. The largest cost was paying for the gas to make tw trips to Lowes to search for washers. Replacing the clutch is way more expensive than that and takes the same amount of work.



Login or Register to Remove Ads
Badbob is offline  
Reply With Quote
Old 10-20-2009, 07:05 PM   #6
james lockhart
Junior Member
 
Join Date: Aug 2009
Location: florida
Posts: 6
Re: How To Fix A Slippery Clutch

do i need to scuff the little black pads that the plates rub against? i didnt, and its worse than it was before?
james lockhart is offline  
Reply With Quote
Old 10-20-2009, 07:54 PM   #7
Easy Rider
Senior Member
 
Join Date: May 2007
Location: Champaign, Illinois
Posts: 4,561
Re: How To Fix A Slippery Clutch

Quote:
Originally Posted by james lockhart
do i need to scuff the little black pads that the plates rub against? i didnt, and its worse than it was before?
Bad Bob hasn't been around much lately.
Anyhow........not everybody agrees with all of his "inovative" solutions.
If I was going to take it apart, I would certainly replace the parts that most commonly wear out.
__________________
Loud pipes risk rights!
Easy Rider is offline  
Reply With Quote
Old 10-20-2009, 11:05 PM   #8
burkbuilds
Senior Member
 
burkbuilds's Avatar
 
Join Date: Mar 2009
Location: Shannon, Georgia
Posts: 1,268
Re: How To Fix A Slippery Clutch

That's great information, amazing pictures and thumbs up to Bad Bob on the post, but does anybody know how much new clutch plates cost? If I'm gonna pull that puppy apart and do all of that work, I'd be inclined to replace them and be done with it than do all the work and possibly not solve my problem. I'm all for saving a buck but I'm also all for not having to do something over again if another $50 bucks worth of parts would insure that I'm done with it and not gonna have to spend another Saturday working on the bike when I could be riding it. I have no idea what clutch plates cost though, maybe over a hundred? Anybody know?
burkbuilds is offline  
Reply With Quote
Old 03-02-2014, 11:50 PM   #9
mainlinecoffee
Senior Member
 
mainlinecoffee's Avatar
 
Join Date: Oct 2013
Location: lexington ky
Posts: 223
Clutch plates were closer to 40-55 last I checked. I think that will be my next buy. Also slip can occur if you use automotive oil with additives instead of mc assuming it's a wet clutch.
mainlinecoffee is offline  
Reply With Quote
Old 03-03-2014, 02:01 AM   #10
Water Warrior 2
Senior Member
 
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
Scuffing down metal clutch plates with emery cloth and varsol will work nicely. I did a few months of that in an auto tranny shop when a clutch plate equipped tranny was in for rebuilding. Just make sure you clean things up real well.
What I find interesting is the plates grip so well in an oil bath. Logic says the plates should slip when lubricated.
Water Warrior 2 is offline  
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:20 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.