Two Leaks, two easy repairs

GZ250 · 04-22-2012, 02:15 PM

The left seal from the exhaust attachment and oil seal from clutch release were leaking. The replacement is cheap and easy. The only thing which could get difficult are the four bolts on the exhaust pipes that could not come out easily because of rust. I used WD40 overnight and also before I was going to start the work and used a slight tapping using a hammer on the bolts. They came out easily. I replaced the old bolts with the new ones as the old were very rusted and some threads were damaged while removing. A bolt near the rear tire has to be removed to loosen the exhaust pipes. Both exhaust pipes are attached together so they move/come out together. It is wise to replace both seals.

The clutch release seal sits under the oil seal plate and comes out easily. The problem was that the inner side of the seal that grips the cam shaft clutch release gets hard and stiff because of time and heat otherwise did not look any different from the new one.

Water Warrior 2 · 04-22-2012, 05:00 PM

Well done. Good pics and a short and simple explanation about the methods used. :2tup:

**jonathan180iq** · 04-23-2012, 02:57 PM

Very well done.
Glad you got this sorted and I'm ever happier that you shared your pics and procedure with us.

This will be stickied.

blaine · 04-23-2012, 06:54 PM

Awesome write up & pics!!!! :cool: :2tup:
The only thing I would like to add is when I had problems with the bolts in the exhaust,I put in studs so you can take the nuts off and not need to worry about galling the threads in the head or worse breaking off the bolts in the head.

:cool:

GZ250 · 04-23-2012, 07:55 PM

Thanks for the appreciation.

Water Warrior 2 · 04-25-2012, 10:23 PM

Quote:

Originally Posted by blaine

Awesome write up & pics!!!! :cool: :2tup:
The only thing I would like to add is when I had problems with the bolts in the exhaust,I put in studs so you can take the nuts off and not need to worry about galling the threads in the head or worse breaking off the bolts in the head.

:cool:

I like that idea. If you put the studs in with red Loktite they will stay put and the nut will be more likely to come off too.

Poppa Blue · 08-19-2012, 12:01 AM

Quick question. I am about to do the exhaust seals. I also like your studs n nuts idea. Would you be so kind to give part numbers?

Thanks in advance!

Water Warrior 2 · 08-19-2012, 03:30 AM

Quote:

Originally Posted by Poppa Blue

Quick question. I am about to do the exhaust seals. I also like your studs n nuts idea. Would you be so kind to give part numbers?

Thanks in advance!

The easiest way would be simple. Any big box hardware will have what you need. Just get some Metric studs and nuts. Same size as the bolts you remove. Take in a bolt as a sample for the correct size.
Also a shop that specializes in nuts an bolts or industrial supplies will have what you need.

fatoldfool · 08-20-2012, 12:31 AM

I am thinking you were really lucky with the WD40, as it is not a penetrating oil. Many years of experience has convinced me KanoKroil cannot be beat as a penetrating oil.

Dupo · 08-21-2012, 08:53 PM

Quote:

Originally Posted by jonathan180iq

Very well done.
Glad you got this sorted and I'm ever happier that you shared your pics and procedure with us.

This will be stickied.

Think we should move this to the how to section for a sticky?

04-22-2012, 02:15 PM	#1
GZ250 Senior Member Join Date: May 2007 Location: North Carolina Posts: 334	Two Leaks, two easy repairs The left seal from the exhaust attachment and oil seal from clutch release were leaking. The replacement is cheap and easy. The only thing which could get difficult are the four bolts on the exhaust pipes that could not come out easily because of rust. I used WD40 overnight and also before I was going to start the work and used a slight tapping using a hammer on the bolts. They came out easily. I replaced the old bolts with the new ones as the old were very rusted and some threads were damaged while removing. A bolt near the rear tire has to be removed to loosen the exhaust pipes. Both exhaust pipes are attached together so they move/come out together. It is wise to replace both seals. The clutch release seal sits under the oil seal plate and comes out easily. The problem was that the inner side of the seal that grips the cam shaft clutch release gets hard and stiff because of time and heat otherwise did not look any different from the new one. __________________ “God creates out of nothing. Wonderful you say. Yes, to be sure, but he does what is still more wonderful: he makes saints out of sinners.” “People understand me so poorly that they don't even understand my complaint about them not understanding me.” --- Søren Kierkegaard --- Login or Register to Remove Ads
	0

04-22-2012, 05:00 PM	#2
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	Re: Two Leaks, two easy repairs Well done. Good pics and a short and simple explanation about the methods used. :2tup:
	0

04-23-2012, 02:57 PM	#3
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,996	Re: Two Leaks, two easy repairs Very well done. Glad you got this sorted and I'm ever happier that you shared your pics and procedure with us. This will be stickied. Login or Register to Remove Ads
	0

04-23-2012, 06:54 PM	#4
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	Re: Two Leaks, two easy repairs Awesome write up & pics!!!! :cool: :2tup: The only thing I would like to add is when I had problems with the bolts in the exhaust,I put in studs so you can take the nuts off and not need to worry about galling the threads in the head or worse breaking off the bolts in the head. :cool: __________________ If at first you do succeed, try not to look surprised.
	0

04-23-2012, 07:55 PM	#5
GZ250 Senior Member Join Date: May 2007 Location: North Carolina Posts: 334	Re: Two Leaks, two easy repairs Thanks for the appreciation. __________________ “God creates out of nothing. Wonderful you say. Yes, to be sure, but he does what is still more wonderful: he makes saints out of sinners.” “People understand me so poorly that they don't even understand my complaint about them not understanding me.” --- Søren Kierkegaard --- Login or Register to Remove Ads
	0

08-19-2012, 12:01 AM	#7
Poppa Blue Junior Member Join Date: Jul 2012 Location: Friendswood Texas USA Posts: 2	Re: Two Leaks, two easy repairs Quick question. I am about to do the exhaust seals. I also like your studs n nuts idea. Would you be so kind to give part numbers? Thanks in advance!
	0

08-20-2012, 12:31 AM	#9
fatoldfool Member Join Date: May 2012 Location: southern WV Posts: 55	Re: Two Leaks, two easy repairs I am thinking you were really lucky with the WD40, as it is not a penetrating oil. Many years of experience has convinced me KanoKroil cannot be beat as a penetrating oil.
	0