Used piston - Page 6

raul10141964 · 07-21-2013, 08:21 PM

you can repair your plug using something like this

ovilc88 · 07-25-2013, 02:24 AM

I can get that and put the plug in its place then fill in the hole I drilled. I can also use the JB KWIK WELD.

ovilc88 · 08-23-2013, 04:12 AM

Finally got'er running today!!!! Woooohoooo!!!! It felt so good feeling and hearing that baby rumble!! I installed a new pilot jet needle, washer, o ring and spring. I got the hole I wasn't suppose to make filled with JB-Weld! Started up on the first crank :grin: I rode her around the neighborhood and it felt like freedom! Just gotta finish putting the exhaust on, little adjustment on the carb replace the little window on the master cylinder, bleed brakes, clean and polish

oh and did I mention I'm SUPER EXCITED!!!!! I want to thank everyone who had a hand in the advice, tips, and encouragement I received from this beautiful forum full of awesome peeps! God Bless!

Water Warrior 2 · 08-23-2013, 08:42 AM

:2tup: :2tup: :2tup: :2tup: :2tup: :2tup: :2tup:

Goose51683 · 08-23-2013, 08:56 AM

Awesome to hear a success story on here!

blaine · 08-23-2013, 09:20 AM

Awesome.Congrats!!!!

**jonathan180iq** · 08-23-2013, 09:46 AM

hmmm....HMMM????......YYYAAAAAAAYYYY!!!!

ovilc88 · 09-08-2013, 10:58 PM

I finally fixed the master cylinder sight glass. Check it....

ovilc88 · 09-08-2013, 11:00 PM

I finish bleeding the brakes and notice that the brake pads are down to metal :/ o well. One more new thing for the bike. I wonder if I can get the rotor cut? Anybody know?

**jonathan180iq** · 09-09-2013, 09:50 AM

You mean like machined? I don't see why not. You'll just need to check the service manual for the minimum thickness and make sure your machinist doesn't exceed that.

07-21-2013, 08:21 PM	#51
raul10141964 Senior Member Join Date: Apr 2012 Location: Elkhart, Indiana Posts: 369	Re: Used piston you can repair your plug using something like this Login or Register to Remove Ads
	0

07-25-2013, 02:24 AM	#52
ovilc88 Member Join Date: Feb 2013 Location: Coral Springs, FL Posts: 73	Re: Used piston I can get that and put the plug in its place then fill in the hole I drilled. I can also use the JB KWIK WELD. __________________ "Marty! We have to go back into the future!" Doc Brown
	0

08-23-2013, 04:12 AM	#53
ovilc88 Member Join Date: Feb 2013 Location: Coral Springs, FL Posts: 73	Re: Used piston Finally got'er running today!!!! Woooohoooo!!!! It felt so good feeling and hearing that baby rumble!! I installed a new pilot jet needle, washer, o ring and spring. I got the hole I wasn't suppose to make filled with JB-Weld! Started up on the first crank :grin: I rode her around the neighborhood and it felt like freedom! Just gotta finish putting the exhaust on, little adjustment on the carb replace the little window on the master cylinder, bleed brakes, clean and polish oh and did I mention I'm SUPER EXCITED!!!!! I want to thank everyone who had a hand in the advice, tips, and encouragement I received from this beautiful forum full of awesome peeps! God Bless! __________________ "Marty! We have to go back into the future!" Doc Brown Login or Register to Remove Ads
	0

08-23-2013, 08:42 AM	#54
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	Re: Used piston :2tup: :2tup: :2tup: :2tup: :2tup: :2tup: :2tup:
	0

08-23-2013, 08:56 AM	#55
Goose51683 Senior Member Join Date: Apr 2013 Location: Indiana Posts: 621	Re: Used piston Awesome to hear a success story on here! Login or Register to Remove Ads
	0

08-23-2013, 09:20 AM	#56
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	Re: Used piston Awesome.Congrats!!!! __________________ If at first you do succeed, try not to look surprised.
	0

08-23-2013, 09:46 AM	#57
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,995	Re: Used piston hmmm....HMMM????......YYYAAAAAAAYYYY!!!!
	0

09-08-2013, 10:58 PM	#58
ovilc88 Member Join Date: Feb 2013 Location: Coral Springs, FL Posts: 73	Re: Used piston I finally fixed the master cylinder sight glass. Check it.... __________________ "Marty! We have to go back into the future!" Doc Brown
	0

09-08-2013, 11:00 PM	#59
ovilc88 Member Join Date: Feb 2013 Location: Coral Springs, FL Posts: 73	Re: Used piston I finish bleeding the brakes and notice that the brake pads are down to metal :/ o well. One more new thing for the bike. I wonder if I can get the rotor cut? Anybody know? __________________ "Marty! We have to go back into the future!" Doc Brown
	0

09-09-2013, 09:50 AM	#60
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,995	Re: Used piston You mean like machined? I don't see why not. You'll just need to check the service manual for the minimum thickness and make sure your machinist doesn't exceed that.
	0