Install a 16 Tooth Front Sprocket - Page 30

**jonathan180iq** · 04-17-2015, 10:51 AM

Quote:

Originally Posted by Water Warrior 2

Shouldn't be enough difference to sweat over at the pumps. A rider's right hand has a lot to do with economy.

+1

My fuel economy was very consistent throughout my ownership.

The sprocket didn't change anything for me, essentially. On long flat stretches, it increased my mileage. On very hilly terrain, my fuel economy decreased. the same would have happened with any sized sprocket.

spldart · 06-20-2015, 09:16 PM

I only just installed my 16t sprocket.
....
....
....
First impression is....
I absolutely love it!

I'll get some mileage numbers and impression of a long commute over the next few days.

Oh. And my primary goal is to reduce engine speed on freeway thus adding longevity.
We shall see how that plays out.

spldart · 06-26-2015, 08:20 AM

Mixed mileage on my commute is unchanged.
And since more rpm equal higher stresses on the engine, and this sprocket lowers engine
rpm in top gear on freeway about 7 percent, I'm thinking this mod is a great one to consider.
I love this mod.

Vegas Street Rider · 09-09-2015, 08:49 PM

After reading the various posts regarding the installation of a 16 t sprocket, I decided to try it for myself. Yesterday, I ordered the sprocket and am looking forward to installing it on my 2009 GZ. I will let you know how I like it. I always felt like I needed to grab another gear after 5th. This should satisfy that feeling.

Thanks for the detailed How To video. It's pretty simple, but following someone else's experience always instills confidence into a project.

raul10141964 · 09-09-2015, 08:55 PM

I recommend to mod the carburetor to recover the lost of power with the 16t sprocket

Sent from my Z813 using Tapatalk

spldart · 09-09-2015, 09:03 PM

Link to carb mod of which you speak?
I wanna try.
Oh. And btw. Changing final drive ratio just moves the power. It doesn't lose it.
I did notice peak power rolls on around 65 mph or more whereas it used to come on sooner final gear.

Vegas Street Rider · 09-10-2015, 01:52 PM

How much torque do you need to tighten the nut for the front sprocket?

Vegas Street Rider · 09-15-2015, 11:47 PM

Put on the 16t sprocket on my 2009 gz. Haven't been able to take it on the beltway at higher speeds but definitely notice the difference in 1st gear and 4th since most of my riding is done at about 45mph on surface streets. I will update you all once I have had a chance to get her out on the highway. I have not noticed a need for the carb jet kit yet but I will consider it after I have ridden for a while.

itsagz250butitsmine · 08-25-2016, 09:43 PM

Thanks for the write up! The verdict is in, I just tried it out and the changes that I've experienced are that each gear adds about 5mph, which made 4th gear reach 70 now with the throttle pinned, but 5th gear had become even weaker

now 5th gear maintains the speed and ever so slowly decelerates to 60. Still, better in every way except 5th, but I was expecting as much.

Vegas Street Rider · 08-25-2016, 11:44 PM

Good news. You should eventually address the power issue though. 5th gear will add life to your engine by keeping the revs down at the higher speeds. Good luck.

06-20-2015, 09:16 PM	#292
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	I only just installed my 16t sprocket. .... .... .... First impression is.... I absolutely love it! I'll get some mileage numbers and impression of a long commute over the next few days. Oh. And my primary goal is to reduce engine speed on freeway thus adding longevity. We shall see how that plays out. Last edited by spldart; 06-20-2015 at 09:20 PM.
	0

06-26-2015, 08:20 AM	#293
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	Mixed mileage on my commute is unchanged. And since more rpm equal higher stresses on the engine, and this sprocket lowers engine rpm in top gear on freeway about 7 percent, I'm thinking this mod is a great one to consider. I love this mod. Login or Register to Remove Ads
	0

09-09-2015, 08:49 PM	#294
Vegas Street Rider Senior Member Join Date: May 2015 Location: Henderson, NV Posts: 1,108	Installing 16t sprocket After reading the various posts regarding the installation of a 16 t sprocket, I decided to try it for myself. Yesterday, I ordered the sprocket and am looking forward to installing it on my 2009 GZ. I will let you know how I like it. I always felt like I needed to grab another gear after 5th. This should satisfy that feeling. Thanks for the detailed How To video. It's pretty simple, but following someone else's experience always instills confidence into a project.
	0

09-09-2015, 08:55 PM	#295
raul10141964 Senior Member Join Date: Apr 2012 Location: Elkhart, Indiana Posts: 369	I recommend to mod the carburetor to recover the lost of power with the 16t sprocket Sent from my Z813 using Tapatalk Login or Register to Remove Ads
	0

09-09-2015, 09:03 PM	#296
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	Link to carb mod of which you speak? I wanna try. Oh. And btw. Changing final drive ratio just moves the power. It doesn't lose it. I did notice peak power rolls on around 65 mph or more whereas it used to come on sooner final gear. Last edited by spldart; 09-09-2015 at 09:50 PM.
	0

09-10-2015, 01:52 PM	#297
Vegas Street Rider Senior Member Join Date: May 2015 Location: Henderson, NV Posts: 1,108	How much torque do you need to tighten the nut for the front sprocket?
	0

09-15-2015, 11:47 PM	#298
Vegas Street Rider Senior Member Join Date: May 2015 Location: Henderson, NV Posts: 1,108	Put on the 16t sprocket on my 2009 gz. Haven't been able to take it on the beltway at higher speeds but definitely notice the difference in 1st gear and 4th since most of my riding is done at about 45mph on surface streets. I will update you all once I have had a chance to get her out on the highway. I have not noticed a need for the carb jet kit yet but I will consider it after I have ridden for a while.
	0

08-25-2016, 09:43 PM	#299
itsagz250butitsmine Junior Member Join Date: Jun 2016 Location: NY, NY Posts: 10	Thanks for the write up! The verdict is in, I just tried it out and the changes that I've experienced are that each gear adds about 5mph, which made 4th gear reach 70 now with the throttle pinned, but 5th gear had become even weaker now 5th gear maintains the speed and ever so slowly decelerates to 60. Still, better in every way except 5th, but I was expecting as much.
	0

08-25-2016, 11:44 PM	#300
Vegas Street Rider Senior Member Join Date: May 2015 Location: Henderson, NV Posts: 1,108	Good news. You should eventually address the power issue though. 5th gear will add life to your engine by keeping the revs down at the higher speeds. Good luck.
	0