Autozone LED kit - Bright as Hell. - Page 3

cayuse · 04-07-2011, 02:44 PM

Try here:
http://www.oznium.com/flexible-motorcycle-leds

Not complete MC kits, but you can buy a few strips and use your imagination.

waya · 04-07-2011, 11:22 PM

Poking around I found this site: http://www.dogvoodoolights.com/

Check out the gallery.

waya · 04-08-2011, 12:02 AM

Better link for the Gallery: http://www.dogvoodoolights.com/gallery.htm

Water Warrior 2 · 04-08-2011, 12:10 AM

I could never do that to the Vstom, all I would do is light up dirt and plastic parts.

waya · 04-08-2011, 12:53 AM

Quote:

Originally Posted by Water Warrior

I could never do that to the Vstom, all I would do is light up dirt and plastic parts.

Heh. Sounds like my car.

cayuse · 04-08-2011, 11:12 AM

Dupo & Burkbuilds,
Did you use 3M tape to fasten your lights? If so, how did that work out in the long run?
I'm just a little concerned about the tape loosening up. I'd hate to have an LED strip fall off into the spokes. :skull:

mole2 · 05-09-2011, 05:53 AM

Quote:

Originally Posted by dannylightning

those are nice and bright, they light up the ground quite well. mine do seem the catch the chrome better but i spent a good amount of time deciding where to place each light.

Danny, where are you. I haven't seen you on here in a long while.

Dupo · 05-09-2011, 02:45 PM

Oznium is the dealer where he was getting his lights for the kit that i have.

Just make sure to get a controller box if you go with the million color strips. Otherwise, they are VERY easy to install ...

Dupo · 05-09-2011, 02:46 PM

Quote:

Originally Posted by cayuse

Dupo & Burkbuilds,
Did you use 3M tape to fasten your lights? If so, how did that work out in the long run?
I'm just a little concerned about the tape loosening up. I'd hate to have an LED strip fall off into the spokes. :skull:

3M, yes. Mine have held up for two years now. I only have one little section that i have to re tape after all that time. Just make sure you clean wherever it is you are going to 3M. Even if one DID happen to fall into the spokes, it would get ripped right off and be road trash in an instant.

burkbuilds · 05-26-2011, 08:32 PM

The 3M would probably be all that is needed, but I used some small cable ties to make sure everything stayed put too.

04-07-2011, 02:44 PM	#21
cayuse Senior Member Join Date: May 2010 Location: Abbotsford, BC Posts: 444	Re: auto zone led kit, bright as hell. Try here: http://www.oznium.com/flexible-motorcycle-leds Not complete MC kits, but you can buy a few strips and use your imagination. __________________ Lovin' every minute of it. 2005 GZ250 (sold after 26000km) 2013 CB500XA Login or Register to Remove Ads
	0

04-07-2011, 11:22 PM	#22
waya Senior Member Join Date: Mar 2011 Location: Marietta, GA Posts: 116	Re: auto zone led kit, bright as hell. Poking around I found this site: http://www.dogvoodoolights.com/ Check out the gallery. __________________ --- Worth the listen: http://www.financialsense.com/financial-sense-newshour
	0

04-08-2011, 12:02 AM	#23
waya Senior Member Join Date: Mar 2011 Location: Marietta, GA Posts: 116	Re: auto zone led kit, bright as hell. Better link for the Gallery: http://www.dogvoodoolights.com/gallery.htm __________________ --- Worth the listen: http://www.financialsense.com/financial-sense-newshour Login or Register to Remove Ads
	0

04-08-2011, 12:10 AM	#24
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	Re: auto zone led kit, bright as hell. I could never do that to the Vstom, all I would do is light up dirt and plastic parts.
	0

04-08-2011, 11:12 AM	#26
cayuse Senior Member Join Date: May 2010 Location: Abbotsford, BC Posts: 444	Re: auto zone led kit, bright as hell. Dupo & Burkbuilds, Did you use 3M tape to fasten your lights? If so, how did that work out in the long run? I'm just a little concerned about the tape loosening up. I'd hate to have an LED strip fall off into the spokes. :skull: __________________ Lovin' every minute of it. 2005 GZ250 (sold after 26000km) 2013 CB500XA
	0

05-09-2011, 02:45 PM	#28
Dupo Senior Member Join Date: Aug 2006 Location: Allentown, Pa Posts: 1,255	Re: auto zone led kit, bright as hell. Oznium is the dealer where he was getting his lights for the kit that i have. Just make sure to get a controller box if you go with the million color strips. Otherwise, they are VERY easy to install ... __________________ Photography Gallery *updated url - new site! Motorcycle Blog Facebook
	0

05-26-2011, 08:32 PM	#30
burkbuilds Senior Member Join Date: Mar 2009 Location: Shannon, Georgia Posts: 1,268	Re: auto zone led kit, bright as hell. The 3M would probably be all that is needed, but I used some small cable ties to make sure everything stayed put too.
	0