Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > GZ250-Specific > Performance

Reply
 
Thread Tools Display Modes
Old 08-15-2014, 04:37 PM   #61
jonathan180iq
Super Moderator
 
jonathan180iq's Avatar
 
Join Date: Jan 2007
Location: Dalton, GA
Posts: 3,996
Drilling holes in the exhaust is kind of a waste. Just wait and save up for a real slip-on muffler at least.

If you're only going with the K&n filter, you won't need a 140 main jet.
Stock is 122.5 or something close. Start with a 125. Maybe a 128 or 130 should cover the intake.

EDIT: (Second thought, just slap a 130-135 on there. Worst case, you'll be a tad rich but that just helps the bike run a little cooler.)

Be sure to order the K&N filter for the GS500. That's the one you want.

Everyone, even stock, should do the needle shim. So go ahead and plan on that too. It's not hard at all.

http://www.gz250bike.com/forum/showthread.php?t=16



Login or Register to Remove Ads
jonathan180iq is offline  
Reply With Quote
Old 08-28-2014, 08:51 PM   #62
Etsola
Junior Member
 
Join Date: Aug 2014
Posts: 3
Hey thanks for the reply ! I had thought I would've had an email notification, but I didn't.

I will probably go for an aftermarket exhaust in a bit, but in the meantime I just wanted it to at least sound better

And yeah, in Canada, stock main jet is #120. So, since we get colder weather, I'll definitely get 130-135-140's to test.

Looking at part #'s, what type of carb is it ? It says MIKUNI BSR32SS, but for jets it only says something like SR ... only 2 letters and there seem to be 2 types of very similar jets. Any idea ?

I already have a small pod filter that I tried to use on my Bandit GSF400 ... but tuning 4 jetted carbs is not that easy at all So I'll reuse it with the GZ ...

I'll probably create a thread with my bobber build.

Also, thanks for the link for the needle

Cheers
Etsola is offline  
Reply With Quote
Old 08-28-2014, 11:16 PM   #63
mainlinecoffee
Senior Member
 
mainlinecoffee's Avatar
 
Join Date: Oct 2013
Location: lexington ky
Posts: 223
For what it's worth I run a 140 just to be cautious,with a pod and slip on you can't be too safe. Plus more fuel never hurt,itl get burnt just the same



Login or Register to Remove Ads
mainlinecoffee is offline  
Reply With Quote
Old 08-29-2014, 11:31 AM   #64
raul10141964
Senior Member
 
Join Date: Apr 2012
Location: Elkhart, Indiana
Posts: 369
carb modding

1) main jet control the maximum amount off fuel available to the engine (part#16) factory 120 upgrade to 140 (I found my at my local motorcycle dealer , look for small mikuni main jet or take the old one with you)

2)needle shine control the fuel at mid range move the washer (part# 9)from the top of the E-ring (part# 10) to under the e-ring to improve the mid range

3) Pilot jet (part#26) control the fuel from idle to about 1/8 of Throttle factory set under 2 turns from the close position new set 2.5 to 3 turns, you may need to remove the plug (part#26A) to gain access, improve idle and reduce the fluctuation be twin col and hot idle

4) Upgrade air filter (I modify the factory filter see second picture)



http://www.gz250bike.com/forum/attac...9&d=1408145033

http://www.gz250bike.com/forum/attac...0&d=1408147180
raul10141964 is offline  
Reply With Quote
Old 12-25-2016, 01:57 PM   #65
pfaffe1
Junior Member
 
Join Date: Dec 2016
Posts: 2
Jetting with original exhaust

Hi, will it gain power to jet the carb and change the airfilter to GS 500 ( without tube inside ) with the original exhaust ?

Can i use the bigger jets from the S40 with 8mm top N100604 ? I have got some in 125, 130, 135

Thanks



Login or Register to Remove Ads
pfaffe1 is offline  
Reply With Quote
Old 06-25-2017, 12:22 PM   #66
pfaffe1
Junior Member
 
Join Date: Dec 2016
Posts: 2
130 Jet instead of 118, PilotScrew 1 3/4, and this airfilter from GS 500 WITH large Tube inside. Not annoying loud and Drives perfekt with much power in all ranges, Floatlevel 13 mm
Attached Images
File Type: jpg GS 500 .jpg (9.2 KB, 3 views)
pfaffe1 is offline  
Reply With Quote
Old 07-02-2017, 09:52 PM   #67
kilo0195
Member
 
Join Date: Jul 2017
Location: Illinois
Posts: 52
I ported, repiped the exhaust to 1.5, installed an emgo shorty glasspack, k&n filter, and rejetted to 147.5. I shimmed the needle by moving the silver washer to the bottom and made some more washer shims by drilling and cutting some pieces of a coke can. I also did the 16t sprocket and it will get up and move with the mods.
kilo0195 is offline  
Reply With Quote
Old 07-12-2017, 06:06 PM   #68
spldart
Senior Member
 
spldart's Avatar
 
Join Date: May 2015
Location: Stafford, Texas
Posts: 604
Unless your gonna bend the heck outta the inlet tube you need to remove the two 10mm bolts either side the airbox and shift it rearward about a centimeter to clear the carbs removal.
spldart is offline  
Reply With Quote
Old 07-12-2017, 06:07 PM   #69
spldart
Senior Member
 
spldart's Avatar
 
Join Date: May 2015
Location: Stafford, Texas
Posts: 604
Oh! And I anxiously await your jet test results mr. 180.
I have found whenever I through some K&Ns on a bike I had to go up 2 or 3 jets.
But I haven't done any mod like that on this bike... yet...
spldart is offline  
Reply With Quote
Old 07-20-2017, 06:12 PM   #70
kilo0195
Member
 
Join Date: Jul 2017
Location: Illinois
Posts: 52
After I put the k&n in it I actually decided to take the air box out. The rubber connector from the carb to box I found actually fits around the top opening of the filter almost perfectly. I them decided to just epoxy the tube directly to the filter and it fits nicely. I was also running a tad rich according to my plug and after this my plug is reading just fine.
kilo0195 is offline  
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:34 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.