Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > GZ250-Specific > Instructional Articles

Reply
 
Thread Tools Display Modes
Old 03-02-2011, 08:58 AM   #1
Joel K-Man
Junior Member
 
Join Date: Feb 2011
Location: South Carolina
Posts: 15
Jumper posts

When I got my bike, I had to jump it off to start it ( the battery was shot). So here is what I did.

On the battery cover on the right side, I drilled two 1/4 inch holes 4 inches apart just after the place where the cover angles at the front. I put a bolt in each one, double nutted, with the bolt heads on the inside of the cover. Then I made two cables out of 12 guage red and black wire about 10 inches long, put terminals on each end and attched them to the bolts. The other ends went to the battery terminals, the red wire to positive and the black to negitive. When I finished them, I attached two large wire nuts to the protruding bolt shafts on the outside of the cover, a red nut on pos. and a black one on neg. Now if I ever need to boost the bike from a car for some reason, I don't have to remove anything and it takes almost no time at all. Just unscrew the wire nuts, clamp on the cables and bust it off. I did use it before I changed the battery out later on, and it works like a charm.



Login or Register to Remove Ads
Joel K-Man is offline  
Reply With Quote
Old 03-02-2011, 10:04 AM   #2
alantf
Senior Member
 
alantf's Avatar
 
Join Date: Nov 2008
Location: Tenerife (Spain)
Posts: 3,719
Re: Jumper posts

Quote:
Originally Posted by Joel K-Man
and it works like a charm.
Until some moron comes along & shorts them out - just to see what happens. Believe me, Murphy's law applies.
__________________
By birth an Englishman, by the grace of God a Yorkshireman.
alantf is offline  
Reply With Quote
Old 03-02-2011, 10:59 AM   #3
mrlmd1
Senior Member
 
Join Date: Jan 2008
Location: Crawfordville, Florida
Posts: 2,853
Re: Jumper posts

Much easier and safer to attach the flat SAE plug that comes with all the little battery chargers/maintainers/tenders and let it hang out somewhere protected beneath the bike or the seat, You can also use that as an accessory plug for a light load like a GPS or phone charger.



Login or Register to Remove Ads
mrlmd1 is offline  
Reply With Quote
Old 03-02-2011, 04:06 PM   #4
jonathan180iq
Super Moderator
 
jonathan180iq's Avatar
 
Join Date: Jan 2007
Location: Dalton, GA
Posts: 3,996
Re: Jumper posts

Plus 1 for the DIYer attitude.

But to be safe, just swing over to your local flea market, buy some electrical connectors and wire for $.50 and make a hidden hook up. Finish it off with rubber plugs so they can't short out on the frame or, like Alan said, some jerk doesn't just jumper them and fry your whole system.

It's a safety hazard for kids too.

"Little Johnny, come back in here with that fork!"
"It's OK Mom! I'll pretend it's my key for uncle Joel's motorcyzzzzzk...... BOOM!"
jonathan180iq is offline  
Reply With Quote
Old 03-02-2011, 05:33 PM   #5
blaine
Senior Member
 
blaine's Avatar
 
Join Date: Feb 2010
Location: P.E.I. Canada
Posts: 3,784
Re: Jumper posts

Quote:
Originally Posted by mrlmd1
Much easier and safer to attach the flat SAE plug that comes with all the little battery chargers/maintainers/tenders and let it hang out somewhere protected beneath the bike or the seat, You can also use that as an accessory plug for a light load like a GPS or phone charger.
Yes,but I think he wanted a easy way to boost the bike without removing the seat & side cover.
:cool:
__________________
If at first you do succeed, try not to look surprised.





Login or Register to Remove Ads
blaine is offline  
Reply With Quote
Old 03-02-2011, 05:48 PM   #6
mrlmd1
Senior Member
 
Join Date: Jan 2008
Location: Crawfordville, Florida
Posts: 2,853
Re: Jumper posts

Just let the wire and plug hang down underneath in a protected site, ziplock it to the frame if you want. It's a no brainer, I have this on my other 3 bikes and it takes only a few minutes to hook up and it's always right there for use. That's much better and safer than having 2 bare battery terminal posts exposed just waiting to be shorted out by some bystander, (WTF is this?) especially without an inline fuse on the + side.
mrlmd1 is offline  
Reply With Quote
Old 03-02-2011, 05:51 PM   #7
alantf
Senior Member
 
alantf's Avatar
 
Join Date: Nov 2008
Location: Tenerife (Spain)
Posts: 3,719
Re: Jumper posts

Quote:
Originally Posted by blaine

Yes,but I think he wanted a easy way to boost the bike without removing the seat & side cover.
No need to remove the side cover, & removing the saddle takes 2 seconds. Better than having exposed terminals on the outside of the bike. :2tup:
__________________
By birth an Englishman, by the grace of God a Yorkshireman.
alantf is offline  
Reply With Quote
Old 03-02-2011, 05:51 PM   #8
Water Warrior 2
Senior Member
 
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
Re: Jumper posts

Might be a lot safer and still handy using the mentioned flat plug and just rolling up some longer wires for a booster cable. Keep it all under the seat, it only takes a few seconds to remove the seat. 6 feet of coiled 12 guage wire with clips on one end and a flat plug on the other should easily fit.
Water Warrior 2 is offline  
Reply With Quote
Old 03-03-2011, 08:34 AM   #9
Joel K-Man
Junior Member
 
Join Date: Feb 2011
Location: South Carolina
Posts: 15
Re: Jumper posts

Quote:
Originally Posted by jonathan180iq
Plus 1 for the DIYer attitude.

But to be safe, just swing over to your local flea market, buy some electrical connectors and wire for $.50 and make a hidden hook up. Finish it off with rubber plugs so they can't short out on the frame or, like Alan said, some jerk doesn't just jumper them and fry your whole system.

It's a safety hazard for kids too.

"Little Johnny, come back in here with that fork!"
"It's OK Mom! I'll pretend it's my key for uncle Joel's motorcyzzzzzk...... BOOM!"
LMAO!!! :crackup :crackup
Joel K-Man is offline  
Reply With Quote
Old 03-03-2011, 08:40 AM   #10
Joel K-Man
Junior Member
 
Join Date: Feb 2011
Location: South Carolina
Posts: 15
Re: Jumper posts

Well, the large wire nuts over the bolts do cover the terminals. I didn't think about someone tampering with them. I will put an inline fuse on though.
Joel K-Man is offline  
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:35 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.