Register Community Calendar Today's Posts Search

Go Back   GZ 250 Forums > GZ250-Specific > Instructional Articles

Reply
 
Thread Tools Display Modes
Old 12-16-2009, 02:05 PM   #1
hugemoth
Junior Member
 
Join Date: Dec 2009
Location: Bend, Oregon
Posts: 15
DIY rear rack

Here's a quick and dirty, cheap and sturdy, aluminum rack made from Home Depot hardware for about $20. It replaces the rear seat. An easy afternoon project requiring only a vise, hack saw, electric drill, and a few hand tools.

This rack is made from a single 8' piece of 1/8" X 1" aluminum bar stock, held together with 10 3/4 X 1/4-20 stainless machine screws and nylock nuts. Dimensions of the rack are 7" X 14". Attachment to the bike is with the 3 existing rear seat bolts and 2 fender bolts. It's sturdy enough to support my 250lb fat ass without bending. My purpose is to attach a plastic milk crate or camping gear.




Login or Register to Remove Ads
hugemoth is offline  
Reply With Quote
Old 12-16-2009, 05:10 PM   #2
Water Warrior 2
Senior Member
 
Join Date: Dec 2006
Location: Squamish B.C Canada
Posts: 11,409
Re: DIY rear rack

I like that. You do nice work.
Water Warrior 2 is offline  
Reply With Quote
Old 12-16-2009, 06:08 PM   #3
alanmcorcoran
Senior Member
 
Join Date: Jul 2008
Location: Anaheim, CA
Posts: 2,926
Re: DIY rear rack

Very nice design and execution. It's been almost 40 years since I took metal shop. Is there a tool that allowed you to do such precise bending of the bar or is it more of a skill?

If you end up with an aftermarket trunk (rather than the milk crate) keep us posted.

Did you replace the stock bolts in the fender with longer ones?
__________________
[hr:5yt6ldkq][/hr:5yt6ldkq]
http://alanmarkcorcoran.com Motorcycles, Music, Musings and Moreā€¦



Login or Register to Remove Ads
alanmcorcoran is offline  
Reply With Quote
Old 12-16-2009, 06:54 PM   #4
hugemoth
Junior Member
 
Join Date: Dec 2009
Location: Bend, Oregon
Posts: 15
Re: DIY rear rack

To get the bends I put the aluminum bar in the vise along side a socket of whatever diameter and just bend it over by hand. Think I used a 13/16 spark plug socket. The aluminum won't take a sharp bend like steel will.

If I use any kind of a trunk it'll just be one of those Rubbermaid containers.

The fender bolts in my Chinese clone are about an inch longer than they need to be so replacement wasn't necessary.

Q
hugemoth is offline  
Reply With Quote
Old 06-10-2010, 05:07 PM   #5
nautec
Junior Member
 
Join Date: May 2010
Location: Tucson
Posts: 10
Re: DIY rear rack

I am curious how this would affect the installation of saddlebags. Not sure how all saddlebags are attached but mine are tied down under the passenger seat and is held in one spot by the passenger seat. I am tempted to try to build this rack large enough to fit over the seat but seems like a waste. One other thought i was pondering was adding a bar or two running lengthwise under the rack to accommodating the saddlebags to stay up and not sit on the muffler. However, this leads to exposing the securing straps to the saddlebags to everyone. Hmm, what to do. Any suggestions?



Login or Register to Remove Ads
nautec is offline  
Reply With Quote
Old 06-10-2010, 05:35 PM   #6
Sarris
Senior Member
 
Join Date: May 2007
Location: New Port Richey, Florida USA
Posts: 1,348
Re: DIY rear rack

You can install the bags by inserting the split throw over tongue behind the fender support rails. The bag support rails need to be installed to create a large enough gap to slip the bag tongue behind the fender support.

See my previous post here: The Sarris GZ... Look about halfway down for the description.

Further explanation here: Further Explanation & Photos

Here is how to make a heat shield (necessary) to keep from burning your right bag. Heat Shield... I have a photo towards the bottom of the page.

:2tup:
__________________
Prudent riders live longer than moron riders.
Sarris is offline  
Reply With Quote
Old 08-07-2010, 08:52 AM   #7
emory70
Senior Member
 
Join Date: Jul 2010
Location: jacksonville fl
Posts: 100
Re: DIY rear rack

when i read "home depot hardware," i instantly rolled my eyes. omg, not another awful hack job. then i looked at your pic. damn, that's pretty nice. good job man.
__________________
STGMTT
emory70 is offline  
Reply With Quote
Reply




Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:26 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.