Well, she finally puked her guts out.... (pic) - Page 7

derbydave · 03-29-2017, 02:12 PM

Are you sure you have oil pressure and adequate oil flow? Valves don't just get loose unless there is some major wear.

spldart · 03-29-2017, 03:43 PM

Quote:

Originally Posted by Pmhearns

Hey blain, i have this too haha, i have stock pipes though...

.

And nice job for the information during the rebuild. Did yhe bottom of the jug by chance have the 2 holes? It appears that in your first several posts, the photo of the top of the jug has the holes and you can see blow by where the gasket didnt cover them properly causing exhaust tk escape and oil to stain the front of the jug. I noticed the NEW jug does not have those holes... any thoughts?

The holes in the old jug are blanks. They go nowhere.
There is a formation that looks like it could have been utilized with those holes but it's completely unmachined.

spldart · 03-29-2017, 03:45 PM

Quote:

Originally Posted by derbydave

Are you sure you have oil pressure and adequate oil flow? Valves don't just get loose unless there is some major wear.

I'm pretty sure I had to readjust because I used generic gasket sealer instead of suzuki-bond between the head upper and lower half.

I'll know more shortly.

spldart · 03-29-2017, 03:45 PM

I'm thinking I should have just used GENUINE SUZUKI PARTS.

spldart · 03-29-2017, 04:17 PM

I don't believe this ish!
Cold start today and motor sounds ok.
Not great but ok.
I'm gonna recheck lash and change the oil and run with it a little longer.

derbydave · 03-29-2017, 05:14 PM

I think you are chasing symptoms. Everything so far including the initial dumping oil don't point too a cylinder problem. I would verify oil pressure and flow unless you like chasing your tail.

If I remember from a previous post you recently did the clutch, The oil pump is driven off of a gear on the carrier for the clutch plates. did something get disturbed when you were in there working on the clutch?

spldart · 03-29-2017, 05:41 PM

Clutch was several thousand miles ago. If I had messed up the pump then it should siezed thousands of miles ago.
Each time I tear down the motor I have lots of oil in the journals and cavities under the camshaft. Even if I only run it a short while.
Even after a 15 second run I just did I have oil dripping from atop the valve springs.

spldart · 03-29-2017, 05:42 PM

Little more work and test drive.

spldart · 03-30-2017, 09:52 PM

I do have 2 unusual few economy checks after engine build. However.... They are so high I don't see how they could be accurate so I'm gonna run yet another mpg test.

Old motor was nearly rock solid 68 mpg.

Noise isn't getting worse and goes away with fully warmed motor.
Valve noise is gone after yesterday adjustment.

Vegas Street Rider · 03-30-2017, 11:16 PM

Sounds like things are moving in the right direction. I will keep my fingers crossed for you.

03-29-2017, 02:12 PM	#61
derbydave Senior Member Join Date: Jan 2017 Location: KS Posts: 103	Are you sure you have oil pressure and adequate oil flow? Valves don't just get loose unless there is some major wear. __________________ 2003 Suzuki GZ250 (Sold) 1986 Suzuki Cavalcade LXE 1986 Suzuki Intruder VS700 Login or Register to Remove Ads
	0

03-29-2017, 04:17 PM	#65
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	I don't believe this ish! Cold start today and motor sounds ok. Not great but ok. I'm gonna recheck lash and change the oil and run with it a little longer. Login or Register to Remove Ads
	0

03-29-2017, 05:14 PM	#66
derbydave Senior Member Join Date: Jan 2017 Location: KS Posts: 103	I think you are chasing symptoms. Everything so far including the initial dumping oil don't point too a cylinder problem. I would verify oil pressure and flow unless you like chasing your tail. If I remember from a previous post you recently did the clutch, The oil pump is driven off of a gear on the carrier for the clutch plates. did something get disturbed when you were in there working on the clutch? __________________ 2003 Suzuki GZ250 (Sold) 1986 Suzuki Cavalcade LXE 1986 Suzuki Intruder VS700
	0

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-29-2017, 03:45 PM	#64
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	I'm thinking I should have just used GENUINE SUZUKI PARTS.
	1

03-29-2017, 05:41 PM	#67
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	Clutch was several thousand miles ago. If I had messed up the pump then it should siezed thousands of miles ago. Each time I tear down the motor I have lots of oil in the journals and cavities under the camshaft. Even if I only run it a short while. Even after a 15 second run I just did I have oil dripping from atop the valve springs.
	0

03-29-2017, 05:42 PM	#68
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	Little more work and test drive.
	0

03-30-2017, 09:52 PM	#69
spldart Senior Member Join Date: May 2015 Location: Stafford, Texas Posts: 604	I do have 2 unusual few economy checks after engine build. However.... They are so high I don't see how they could be accurate so I'm gonna run yet another mpg test. Old motor was nearly rock solid 68 mpg. Noise isn't getting worse and goes away with fully warmed motor. Valve noise is gone after yesterday adjustment.
	0

03-30-2017, 11:16 PM	#70
Vegas Street Rider Senior Member Join Date: May 2015 Location: Henderson, NV Posts: 1,108	Sounds like things are moving in the right direction. I will keep my fingers crossed for you.
	1