No/slow acceleration. No top end. - Page 4

GilHirien · 07-27-2014, 10:23 PM

Clutch. Cable. Play.

Update! Thinking it might be my clutch slipping, I was reading through some other threads on here when I realized I had moved my clutch cable at the handlebar while checking other things with my bike. I went outside to check if I had put it back. I hadn't. Now its adjusted properly and runs great!!! Thank you guys for all your help. Also, after a day, the filter is letting gas though just fine on run, where it was slow before. Now I just have to fix an oil leak at the valve inspection caps and she'll be better than when I got her

gz4me + · 07-27-2014, 11:06 PM

I was wondering about that cable last night. Glad you found the problem. Have fun riding the GZ.

mole2 · 07-28-2014, 01:18 AM

Quote:

Originally Posted by GilHirien

Mole, that is the exact filter I have installed. It is not letting enough fuel through fast enough to keep the motor fed.

This one looks similar to the Briggs and Straton fuel filter. These small engines do not have a fuel pump so unless that filter clogged up fast it should work. Also, take the fuel switch out of PRI. It can cause fuel to leak down into the engine if your needle should not seal perfectly causing all sorts of problems.

http://www.ebay.com/itm/Visu-In-Line...37425e&vxp=mtr

GilHirien · 07-29-2014, 08:20 PM

New problem. On a decent trip of about 35 miles to register for classes this fall, my clutch lever begins to ease back to the handlebar over about a minute give or take, then I have no clutch. I had to finish the trip with zero clutch which I can tell you got pretty crazy. Ideas? Seems like it might be the cluch push piece has worked its way unscrewed, but this should NOT happen right? I remember there being a lock nut which had to be tightened (which I did). Should I have used loctite in there? Too late to open her up today so for now it is a mystery which will likely have to wait until this weekend...

GilHirien · 07-30-2014, 08:44 AM

So I just went out and did it last night anyway. The lock nut had come off completely, but I found it with little effort. Cleaned it up along with the adjuster screw and loctite on both. Problem solved. Again.

**jonathan180iq** · 07-30-2014, 09:28 AM

It's amazing what problems little things like a lock nut can create - You'll be rollin' worry-free now.

Rookie Rider · 08-01-2014, 02:11 PM

This was a very helpfull thread by all of you. Glad youre up and rolling again.

07-27-2014, 10:23 PM	#31
GilHirien Member Join Date: Aug 2012 Location: Hattiesburg, MS Posts: 37	Clutch. Cable. Play. Update! Thinking it might be my clutch slipping, I was reading through some other threads on here when I realized I had moved my clutch cable at the handlebar while checking other things with my bike. I went outside to check if I had put it back. I hadn't. Now its adjusted properly and runs great!!! Thank you guys for all your help. Also, after a day, the filter is letting gas though just fine on run, where it was slow before. Now I just have to fix an oil leak at the valve inspection caps and she'll be better than when I got her Login or Register to Remove Ads
	0

07-30-2014, 08:44 AM	#35
GilHirien Member Join Date: Aug 2012 Location: Hattiesburg, MS Posts: 37	So I just went out and did it last night anyway. The lock nut had come off completely, but I found it with little effort. Cleaned it up along with the adjuster screw and loctite on both. Problem solved. Again. Login or Register to Remove Ads
	0

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-27-2014, 11:06 PM	#32
gz4me + Senior Member Join Date: Sep 2013 Location: Santa Maria, California Posts: 234	I was wondering about that cable last night. Glad you found the problem. Have fun riding the GZ.
	0

07-29-2014, 08:20 PM	#34
GilHirien Member Join Date: Aug 2012 Location: Hattiesburg, MS Posts: 37	New problem. On a decent trip of about 35 miles to register for classes this fall, my clutch lever begins to ease back to the handlebar over about a minute give or take, then I have no clutch. I had to finish the trip with zero clutch which I can tell you got pretty crazy. Ideas? Seems like it might be the cluch push piece has worked its way unscrewed, but this should NOT happen right? I remember there being a lock nut which had to be tightened (which I did). Should I have used loctite in there? Too late to open her up today so for now it is a mystery which will likely have to wait until this weekend...
	0

07-30-2014, 09:28 AM	#36
jonathan180iq Super Moderator Join Date: Jan 2007 Location: Dalton, GA Posts: 3,996	It's amazing what problems little things like a lock nut can create - You'll be rollin' worry-free now.
	0

08-01-2014, 02:11 PM	#37
Rookie Rider Senior Member Join Date: Jun 2011 Location: Queens, NYC Posts: 1,263	This was a very helpfull thread by all of you. Glad youre up and rolling again.
	0