Cleaned Carb wont run correctly.

dodie · 03-05-2017, 08:33 PM

I cleaned the carb, it wasnt bad pretty clean. Installed a new k&n air filter also drilled the plug out on the pilot screw. The bike will start. The bike will run at a higher rpm although it will stall after a short time. Like it burns all the fuel in the bowl then stalls. I also can set the idle at a higher rpm it will run until I adjust the screw to a normal idling rpm then it will stall. I tried running the bike on prime thinking maybe it wast filling the bowl fast enough but it did the same thing (stall after a few minutes). Tomorrow Im gonna take the pet cock off and see if its clogged up. How many turns should I set the pilot screw at. The screw under the plug I drilled out. I dont see any vacuum leaks on the 2 rubber hoses the rubber looks good. It ran ok but not great when we put it away for winter. It used to surge aka to lean. I was trying to richen it up but putting a new high flow air filter on I may of made it even leaner. Any suggestions?

blaine · 03-05-2017, 08:39 PM

With the free flowing filter you may need to go to a larger Main jet.Pull your plug & see if still lean....2 1/2 turns out is a good starting point for pilot screw....Out is richer....In leaner.

dodie · 03-08-2017, 07:27 PM

I looked at the spark plug it was black, way to rich. which makes no sense to me. I cleaned the carb put on a new choke spring, also put on a new left switch/choke assembly on the handlebar, put on a new k&n high flow air filter if anything it should be lean. If I cant figure a single carb engine its gonna suck doing a 4 carb system.I put my finger on the vaccuum line to the petcock it sucks hard leaves a ring on my finger. No vacuum leaks.The bike runs. If I make an idle speed adjustment it takes about a minute for it to make any difference in engine rpm then it will stall. The pilot screw seems to make no audible difference in engine sound or rpm. I can spray some starting fluid around the intake boot and air box boot .It makes no change in engine rpm so I know its a sealed system.Any help?

blaine · 03-08-2017, 07:55 PM

Has me wondering if your new choke assembly is operating properly & not sticking on.??

dodie · 03-08-2017, 08:15 PM

Quote:

Originally Posted by blaine

Has me wondering if your new choke assembly is operating properly & not sticking on.??

I really dont like the choke system on these GZ carbs. I prefer a butterfly valve type. This is my wifes bike she is upgrading to an S40 soon.

blaine · 03-08-2017, 09:56 PM

Quote:

Originally Posted by dodie

I really dont like the choke system on these GZ carbs. I prefer a butterfly valve type. This is my wifes bike she is upgrading to an S40 soon.

A lot of bikes have this type...which is actually a "Enricher" more so than a choke..Just uncovers another jet that lets more fuel into the carb.

wacio · 03-08-2017, 10:55 PM

Very important first step if you suddenly run reach is to check:
- if the float valve is working
- oring around that valve not leaking
- floats not cracked
- fuel level set correctly
Any failure of the any item above will cause flooding and running rich.

dodie · 03-09-2017, 01:32 PM

I can put it on prime and it doesnt overflow the carb. I used to have a concours and they are bad about hydrolock.

dodie · 03-19-2017, 06:55 PM

Is it possible to be rich at idle and lean at higher rpm? It idles pretty good I set the float. It idles pretty good now but bogs when in gear and under a load at mid to higher rpm.

dodie · 03-19-2017, 08:38 PM

Well my bad I had put the main jet in the idle circuit and the idle jet in the main jet. Its now behaving normal but bogging at mid rpm, Probly need a bigger main jet.

03-05-2017, 08:33 PM	#1
dodie Junior Member Join Date: Nov 2016 Posts: 8	Cleaned Carb wont run correctly. I cleaned the carb, it wasnt bad pretty clean. Installed a new k&n air filter also drilled the plug out on the pilot screw. The bike will start. The bike will run at a higher rpm although it will stall after a short time. Like it burns all the fuel in the bowl then stalls. I also can set the idle at a higher rpm it will run until I adjust the screw to a normal idling rpm then it will stall. I tried running the bike on prime thinking maybe it wast filling the bowl fast enough but it did the same thing (stall after a few minutes). Tomorrow Im gonna take the pet cock off and see if its clogged up. How many turns should I set the pilot screw at. The screw under the plug I drilled out. I dont see any vacuum leaks on the 2 rubber hoses the rubber looks good. It ran ok but not great when we put it away for winter. It used to surge aka to lean. I was trying to richen it up but putting a new high flow air filter on I may of made it even leaner. Any suggestions? Login or Register to Remove Ads
	0

03-05-2017, 08:39 PM	#2
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	With the free flowing filter you may need to go to a larger Main jet.Pull your plug & see if still lean....2 1/2 turns out is a good starting point for pilot screw....Out is richer....In leaner. __________________ If at first you do succeed, try not to look surprised.
	1

03-08-2017, 07:27 PM	#3
dodie Junior Member Join Date: Nov 2016 Posts: 8	I looked at the spark plug it was black, way to rich. which makes no sense to me. I cleaned the carb put on a new choke spring, also put on a new left switch/choke assembly on the handlebar, put on a new k&n high flow air filter if anything it should be lean. If I cant figure a single carb engine its gonna suck doing a 4 carb system.I put my finger on the vaccuum line to the petcock it sucks hard leaves a ring on my finger. No vacuum leaks.The bike runs. If I make an idle speed adjustment it takes about a minute for it to make any difference in engine rpm then it will stall. The pilot screw seems to make no audible difference in engine sound or rpm. I can spray some starting fluid around the intake boot and air box boot .It makes no change in engine rpm so I know its a sealed system.Any help? Login or Register to Remove Ads Last edited by dodie; 03-08-2017 at 07:40 PM.
	0

03-08-2017, 07:55 PM	#4
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	Has me wondering if your new choke assembly is operating properly & not sticking on.?? __________________ If at first you do succeed, try not to look surprised.
	1

03-08-2017, 10:55 PM	#7
wacio Senior Member Join Date: Apr 2016 Location: Illinois Posts: 174	Very important first step if you suddenly run reach is to check: - if the float valve is working - oring around that valve not leaking - floats not cracked - fuel level set correctly Any failure of the any item above will cause flooding and running rich. Last edited by wacio; 03-08-2017 at 10:58 PM.
	1

03-09-2017, 01:32 PM	#8
dodie Junior Member Join Date: Nov 2016 Posts: 8	I can put it on prime and it doesnt overflow the carb. I used to have a concours and they are bad about hydrolock.
	0

03-19-2017, 06:55 PM	#9
dodie Junior Member Join Date: Nov 2016 Posts: 8	Is it possible to be rich at idle and lean at higher rpm? It idles pretty good I set the float. It idles pretty good now but bogs when in gear and under a load at mid to higher rpm.
	0

03-19-2017, 08:38 PM	#10
dodie Junior Member Join Date: Nov 2016 Posts: 8	Well my bad I had put the main jet in the idle circuit and the idle jet in the main jet. Its now behaving normal but bogging at mid rpm, Probly need a bigger main jet.
	0

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode