07-18-2008, 12:25 AM | #2 |
Senior Member
|
If you just bought the bike, you really should download the Manual and read it over very carefully. This will explain the chain tightening process and everything involved.
http://www.gz250bike.com/viewtopic.php?t=29 The basic principle is to loosen the rear axle and adjust the push screws on the back of the frame/swingarms to pull the tire away from the engine, thus tightening the chain to spec (5-15mm slack). Then retighten the rear axle to the appropriate torque and replace the cotter pin with a new one (highly recommended). Also, ONE post asking the question will usually get you the answer if the search feature doesn't come up with it first. Three posts spanning the forums is not the way to get any sort of respect around here.
__________________
]I am hiding in Honduras. I am a desperate man. Send lawyers, guns and money. The shit has hit the fan. |
|
07-20-2008, 12:38 AM | #3 |
Senior Member
Join Date: Oct 2007
Location: HoCo, Maryland
Posts: 1,349
|
Be careful and make sure that the chain is at its tightest before you tighten it. Move the bike slowly forward and test its slack with your foot, every say 15 cm/6 inches, or if you have it on a stand, roll the wheel by hand) because often, chain slack is different at different positions - the sprockets nor the chain are perfect. I also would not tighten it to the minimum 5 mm, rather to say 12 mm.
My bike has almost 2400 miles and the chain has not needed any tightening.
__________________
2005 "Saturn Black", stock + tach Login or Register to Remove Ads |
|
07-20-2008, 02:28 AM | #4 |
Senior Member
|
Mine needed it when I bought it used. It was, however, mentioned upfront that it needed tightening.
__________________
]I am hiding in Honduras. I am a desperate man. Send lawyers, guns and money. The shit has hit the fan. |
|
07-20-2008, 12:04 PM | #5 |
Junior Member
Join Date: Jul 2008
Posts: 4
|
Thanks Guys really helped, however for anyone doing this, there are about 6 marks on the frame of the bike by the axle and when you are moving the wheel back make sure the marks of the axles bolt line up perfectly with the other side because then the sprocket willl not be positioned properly, Thanks again to everyone for the help
Jp Login or Register to Remove Ads |
|
06-24-2010, 04:23 PM | #6 |
Member
Join Date: Jun 2010
Location: Chicago suburbs
Posts: 65
|
Re: How to tighten the chain
Can you buy a new cotter pin at any hardware store or Walmart? Or is it a dealer-only part?
|
|
06-24-2010, 04:31 PM | #7 | |
Senior Member
Join Date: May 2007
Location: Champaign, Illinois
Posts: 4,561
|
Re: How to tighten the chain
Quote:
Truth be known, about any kind of wire will work; even the old pin, if it doesn't break when being re-installed.
__________________
Loud pipes risk rights! |
|
|
06-24-2010, 06:43 PM | #8 | ||
Senior Member
Join Date: Feb 2010
Location: P.E.I. Canada
Posts: 3,784
|
Re: How to tighten the chain
Quote:
I use a clip pin,reusable,and much easier to remove & replace. :2tup: |
||
|
06-24-2010, 06:44 PM | #9 |
Member
Join Date: Jun 2010
Location: Chicago suburbs
Posts: 65
|
Re: How to tighten the chain
Thanks guys!
|
|
06-25-2010, 06:36 PM | #10 | ||
Junior Member
Join Date: May 2010
Location: Detroit, Michigan
Posts: 16
|
Re: How to tighten the chain
Quote:
Cotter pins should not be reused.
__________________
My boring rides consist of - 1993 Oldsmobile Cutlass Supreme SL 1997 Pontiac Sunfire SE "Cocaine is a hell of a drug." -Rick James |
||
|
|
|