I bought a 2006 gz250

tndoug99 · 07-11-2010, 11:56 PM

I bought a 2006 gz250 w/5300 miles, with a broken valve for $100. The top end was laying in pieces in a box. I believe I have all the parts, but wont know until I start putting it back together. The valve had broken and was stuck to the inside of the head about a 1/4" deep. I pulled it out and it left a small hole right beside the valve seat. I believe I can put a little JB weld to fill the hole since it is small and not too deep. I will post a pic later showing the damage to get some advice on repairing the head. I've already downloaded the manuals to get started.

[center:37e7gv4h]

[/center:37e7gv4h]

BillInGA · 07-12-2010, 12:27 AM

Welcome to the forum.

I'd say you got a pretty good deal, assuming the lunched valve was the only problem with it. Instead of JB Weld, you may want to consider a new cylinder head. You can pick up a new cylinder head assembly from CheapCycleParts.com for less than $500.

BTW, which valve was that broke?

blaine · 07-12-2010, 12:30 AM

Welcome to the forum.IMO J.B weld will not hold up under the high heat & pressures of the cylinder head.Will crumble & fall out and get into rings & bearings,waisting whats left of a low mileage engine,not to mention all your hard work and time.Maybe a machine shop can aluminum weld it as long as it's not in the combustion chamber.

:yes:

Water Warrior 2 · 07-12-2010, 12:57 AM

Assuming there is only damage to the head I would be tempted to just get another head and assorted parts to reassemble the engine.

mole2 · 07-12-2010, 01:50 AM

Welcome aboard. I agree with the others. If the JB weld works free you'll wipe out the engine. Get a new head.

tndoug99 · 07-12-2010, 08:24 AM

Here is a pic of the head. The hole is visible beside the exhaust port. I have ruled JB weld out. I don't want to spend a lot of money on the bike because I am not planning to keep it.

[center:inndxywy]

[/center:inndxywy]

blaine · 07-12-2010, 10:04 AM

If you don't want to spend the money to buy a new or good used head maybe you should consider selling it "as is" or parting it out.Either way it's worth more than you paid for it; if that's what you are intrested in.I would gladly buy it if I lived much closer.They are pretty rare around here.

:drool: O_o

Easy Rider · 07-12-2010, 10:59 AM

Quote:

Originally Posted by blaine

Either way it's worth more than you paid for it.......

Quite a bit more, I would think.

As for the head, that looks more like a dent than a hole. If that's the case, you might get by with just leaving it as is.
BUT.....
If the valve fell into the chamber and then the piston pounded the stem against the head to make that mark........I'd be more worried about the piston than that dent. Could have damaged the bearings, bent the rod or the crank too (not likely but possible).

blaine · 07-12-2010, 11:24 AM

Quote:

Originally Posted by Easy Rider

As for the head, that looks more like a dent than a hole. If that's the case, you might get by with just leaving it as is..

To me that dent looks to be very close to the valve seat.If left "as is" I would be afraid of valves burning in a very short time.

:skull:

Easy Rider · 07-12-2010, 01:54 PM

Quote:

Originally Posted by blaine

To me that dent looks to be very close to the valve seat.If left "as is" I would be afraid of valves burning in a very short time.

Good point.

07-11-2010, 11:56 PM	#1
tndoug99 Junior Member Join Date: Jul 2010 Location: Memphis Posts: 5	I bought a 2006 gz250 I bought a 2006 gz250 w/5300 miles, with a broken valve for $100. The top end was laying in pieces in a box. I believe I have all the parts, but wont know until I start putting it back together. The valve had broken and was stuck to the inside of the head about a 1/4" deep. I pulled it out and it left a small hole right beside the valve seat. I believe I can put a little JB weld to fill the hole since it is small and not too deep. I will post a pic later showing the damage to get some advice on repairing the head. I've already downloaded the manuals to get started. [center:37e7gv4h][/center:37e7gv4h] Login or Register to Remove Ads
	0

07-12-2010, 12:27 AM	#2
BillInGA Senior Member Join Date: Apr 2010 Location: Kennesaw, GA Posts: 296	Re: I bought a 2006 gz250 Welcome to the forum. I'd say you got a pretty good deal, assuming the lunched valve was the only problem with it. Instead of JB Weld, you may want to consider a new cylinder head. You can pick up a new cylinder head assembly from CheapCycleParts.com for less than $500. BTW, which valve was that broke? __________________ ATGATT - All The Gear, All The Time
	0

07-12-2010, 12:30 AM	#3
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	Re: I bought a 2006 gz250 Welcome to the forum.IMO J.B weld will not hold up under the high heat & pressures of the cylinder head.Will crumble & fall out and get into rings & bearings,waisting whats left of a low mileage engine,not to mention all your hard work and time.Maybe a machine shop can aluminum weld it as long as it's not in the combustion chamber. :yes: __________________ If at first you do succeed, try not to look surprised. Login or Register to Remove Ads
	0

07-12-2010, 12:57 AM	#4
Water Warrior 2 Senior Member Join Date: Dec 2006 Location: Squamish B.C Canada Posts: 11,409	Re: I bought a 2006 gz250 Assuming there is only damage to the head I would be tempted to just get another head and assorted parts to reassemble the engine.
	0

07-12-2010, 01:50 AM	#5
mole2 Senior Member Join Date: Dec 2009 Location: Longs, SC Posts: 1,469	Re: I bought a 2006 gz250 Welcome aboard. I agree with the others. If the JB weld works free you'll wipe out the engine. Get a new head. __________________ 2009 V-Star 650 Silverado Pearl White 2007 Suzuki GZ250 Black (sold) Login or Register to Remove Ads
	0

07-12-2010, 08:24 AM	#6
tndoug99 Junior Member Join Date: Jul 2010 Location: Memphis Posts: 5	Re: I bought a 2006 gz250 Here is a pic of the head. The hole is visible beside the exhaust port. I have ruled JB weld out. I don't want to spend a lot of money on the bike because I am not planning to keep it. [center:inndxywy][/center:inndxywy]
	0

07-12-2010, 10:04 AM	#7
blaine Senior Member Join Date: Feb 2010 Location: P.E.I. Canada Posts: 3,784	Re: I bought a 2006 gz250 If you don't want to spend the money to buy a new or good used head maybe you should consider selling it "as is" or parting it out.Either way it's worth more than you paid for it; if that's what you are intrested in.I would gladly buy it if I lived much closer.They are pretty rare around here. :drool: O_o __________________ If at first you do succeed, try not to look surprised.
	0