|
|
03-25-2018, 11:47 PM
|
#1 |
|
Junior Member
Join Date: Mar 2018
Posts: 6
|
Bike won't stay running.
Hi All.
I recently purchased a 2001 GZ250 as a beginner bike to learn to ride on. After the first few weeks of having it, it ran fine, and now I can't keep it started. When I start the bike I have to hold the throttle all the way open to get it going and it stalls as soon as I release it to an idle. Any suggestions on where to begin on figuring out my issue? Login or Register to Remove Ads |
|
|
|
03-26-2018, 07:46 AM
|
#2 |
|
Senior Member
Join Date: Jan 2013
Location: Murcia, Spain
Posts: 683
|
Sounds like you need some maintenance on the carb. Others will be along shortly to advise. Good luck.
__________________
"It begins here for me on this road. How the whole mess happened I don't know, but I know it couldn't happen again in a million years." (Johnny Strabbler-The Wild One 1953) |
|
|
|
|
03-26-2018, 08:31 AM
|
#3 |
|
Senior Member
Join Date: Feb 2010
Location: P.E.I. Canada
Posts: 3,784
|
Welcome.....You can try some SeaFoam in a fresh tank of fuel.....It may take over night to see any results.
__________________
If at first you do succeed, try not to look surprised. 
Login or Register to Remove Ads |
|
|
|
|
03-26-2018, 11:05 AM
|
#4 |
|
Junior Member
Join Date: Mar 2018
Posts: 6
|
Thank you for the replies. I’ve been having these issues I tried sea foam and it still persisted on messing up. I also rebuilt my carb and it’s still acting this way.
Got my endorsement recently and all I wanna do is ride the damn thing. |
|
|
|
|
03-26-2018, 11:48 AM
|
#5 |
|
Senior Member
Join Date: Jan 2017
Location: KS
Posts: 103
|
Did you rebuild the carb in an effort to fix this problem? Did you drill out the plug and service the pilot circuit?
__________________
2003 Suzuki GZ250 (Sold) 1986 Suzuki Cavalcade LXE 1986 Suzuki Intruder VS700 Login or Register to Remove Ads |
|
|
|
|
03-26-2018, 12:21 PM
|
#6 |
|
Junior Member
Join Date: Mar 2018
Posts: 6
|
Yes I rebuilt the carb to try and fix the problem. That’s what someone recommended Me to do. I did not drill anything. I did not drill out plug and service pilot circuit.
|
|
|
|
|
03-26-2018, 12:36 PM
|
#7 |
|
Senior Member
Join Date: Jan 2017
Location: KS
Posts: 103
|
The pilot circuit needs at the very least to be cleaned and have a new O-Ring installed. If you bought a carb kit it probably came with a tiny O-ring. That one is for the pilot. There is a brass plug on the underside of the front of the carb that needs to be carefully drilled out to access the pilot circuit. The plug (see pic) is only about 1/8" thick and under it is the pilot screw. Drill too far and you can damage the screw. After the plug is out unscrew the pilot needle and clean everything taking care not to damage the needle or spring. Screw in the pilot needle gently until it bottoms and then back it out 2 1/2 turns. Adjust further from there based on how it runs. No need to replace the plug
__________________
2003 Suzuki GZ250 (Sold) 1986 Suzuki Cavalcade LXE 1986 Suzuki Intruder VS700 |
|
|
|
|
03-26-2018, 01:00 PM
|
#8 |
|
Junior Member
Join Date: Mar 2018
Posts: 6
|
Yeah I believe I replaced that it’s got a needle point at the tip a spring and o ring so it had to be screwed in at a certain point? Sorry newbie here haha
|
|
|
|
|
03-26-2018, 01:02 PM
|
#9 |
|
Senior Member
Join Date: Jan 2017
Location: KS
Posts: 103
|
How far did you back out the screw once it hit bottom?
__________________
2003 Suzuki GZ250 (Sold) 1986 Suzuki Cavalcade LXE 1986 Suzuki Intruder VS700 |
|
|
|
|
03-26-2018, 01:52 PM
|
#10 |
|
Junior Member
Join Date: Mar 2018
Posts: 6
|
Yeah wasn’t sure if it was suppose to go all the way in or not. You can see the pinhead through the open part of the carb
|
|
|
|
 |
|
|
Hybrid Mode
