El Diablo
07-10-2008, 04:08 PM
Had trouble both ways. I needed to take the cycle into the shop for 600 mile service and didn't have anyone to pick me up if I drove it in so decided to take it in my Ford F150. I used the ramp I used to load my 4 wheeler which I have done hundreds of times.
Loading. Tailgate down, ramp attached, riding it up and why am I not going anywhere? At the top of the ramp with front wheel in bed, the angle was too sharp and the frame sat down squarely on the top of the ramp. I wasn't going anywhere. Was able to get off the bike and tie it down with tie downs using hooks at the back of the truck bed. Next I got my floor jack and jacked up the ramp to lessen the angle and was able to then push the bike forward and load it up.
Well, lesson learned, that won't happen to me again. Picked the bike back up today (they have a nice ramp at the dealer). Go home and:
Unloading. This time I unhook the cables attaching the tailgate to the bed so it hangs down at an angle. That ought to do it. Put my ramp on, yep that looks good. Thank goodness I changed out of my loafers and put on some motorcycle boots just prior to unloading. I have in my truck bed one of those mats so that objects don't slide around. The thing is old and had been used for my last three trucks. As I start to back down slowly, I stop at intervals to adjust my feet, just taking it slow and easy. With the back wheel on the ramp and the front still in the bed, I apply the front break and the mat that it is on starts to slide backwards! This has the bike going backwards with me trying hard to keep my feet moving enough to not fall over but stop the bike at the same time. I manage to stop it after a foot slide. I called for my daughter (15 years old) and she came out, and got in the bed to add weight so it won't slide again as I start back down. It did slide another few inches, but I made it down safely from there.
No scratches but a bit stressful. I think I'll use my 4 X 8 trailer from now on if need be.
Wanted to post as a warning to just be careful. :blush:
Loading. Tailgate down, ramp attached, riding it up and why am I not going anywhere? At the top of the ramp with front wheel in bed, the angle was too sharp and the frame sat down squarely on the top of the ramp. I wasn't going anywhere. Was able to get off the bike and tie it down with tie downs using hooks at the back of the truck bed. Next I got my floor jack and jacked up the ramp to lessen the angle and was able to then push the bike forward and load it up.
Well, lesson learned, that won't happen to me again. Picked the bike back up today (they have a nice ramp at the dealer). Go home and:
Unloading. This time I unhook the cables attaching the tailgate to the bed so it hangs down at an angle. That ought to do it. Put my ramp on, yep that looks good. Thank goodness I changed out of my loafers and put on some motorcycle boots just prior to unloading. I have in my truck bed one of those mats so that objects don't slide around. The thing is old and had been used for my last three trucks. As I start to back down slowly, I stop at intervals to adjust my feet, just taking it slow and easy. With the back wheel on the ramp and the front still in the bed, I apply the front break and the mat that it is on starts to slide backwards! This has the bike going backwards with me trying hard to keep my feet moving enough to not fall over but stop the bike at the same time. I manage to stop it after a foot slide. I called for my daughter (15 years old) and she came out, and got in the bed to add weight so it won't slide again as I start back down. It did slide another few inches, but I made it down safely from there.
No scratches but a bit stressful. I think I'll use my 4 X 8 trailer from now on if need be.
Wanted to post as a warning to just be careful. :blush: